BD40266 strong acid corrosion resistant repairing epoxy floor coatings
Product usage:
This product is a three-component acid resistant protective coating,suitable for preparation of protective coating on the floor surface or wall surface of pharmaceutical, biological, chemical and other enterprises that
are easy to be corroded by strong acid.’
Performance Features:
1, can resist all kinds of strong acid corrosion, not easy to change color;
2. Smooth and delicate surface, easy to clean and maintain;
3. Good adhesion, high mechanical strength, low shrinkage after curing, it can be coated and molded once.
Physical and chemical parameters:
Table of physical and mechanical properties |
||||||
Color |
Physical state |
Density |
Compressive strength |
Bending strength (Mpa) |
Tensile strength (Mpa) |
Hardness |
Grey/green/blue |
fluid |
1.42 |
65 |
48 |
23 |
73 |
Usage and curing characteristics table (experimental conditions: temperature 25¡æ±2¡æ, relative humidity 55%±5%) |
||||
Construction method |
Operational time limit |
Curing time |
Working temperature |
The highest temperature resistant |
Blade coating/rolling coating/brush coating |
30 min |
24 hours |
-60¡æ-120¡æ |
150¡æ |
Medium resistant test data sheet |
|||||
15% |
20% |
30% |
5% |
|
50% |
The mass change rates of test blocks immersed in the above medium for 30 days at room temperature (25¡æ±2¡æ) were all ≤ 1% |
How to use:
1. Surface treatment: clean the surface of the original floor,use the grinding miller to carry out a comprehensive grinding,so that the damaged,sand-raising, cracking,empty drum parts are completely exposed and polished to
the dense substrate,repair the defective parts should be repaired to be flat.The surface of the treated floor shall be flat,compact and dry,without greasy dirt and loose & fragile particles.
2. The preparation: make the A and C two components of repairing agent mix uniformly according to the repaired weight ratio,then place the B components in the required ratio into the A and C mixed materials,mix them uniformly again.
The mixed prepared material should be used up within the specified operating time limit(that is, before the material starts to become sticky, and the material after becoming sticky and hard can’t be used again).
3. Coating: make the uniform mixing materials be brush coating,rolling coating or blade coating on the surface of the floor with trowel,should pay attention to controlling coating thickness.
4. Curing: It can be put into using after curing for 24 hours at room temperature 25¡æ.
Special version:
1.The product parameter is obtained for laboratory testing,only for reference,due to the actual working condition is more complex,suggest the users to do the pretest according to actual working condition.
2.When the environment temperature is below 25¡æ,the curing time will prolong,should take proper heating measure
3.When the environment temperature is more than 25¡æ or the mixing quantity is too large,the curing speed will expedite,should properly shorten the application time of coating after mixing.
Construction protective measures:
1.Wear the protective masks,wear the protective glasses and rubber gloves
2.Need washing hands with soap before eating,drinking or smoking.
3.The health hazard after touching: a few people will have skin allergy phenomenon,see a doctor in time and avoid touching with this product again.should wipe it with ethyl acetate when the sizing material paste on the skin by careless,then wash
it with clear water.Should wash it with clear water immediately and see a doctor when splashing into the eyes by careless.
Warm Prompt:
Residual adhesive solution cured products are non-toxic harmless organic solid,but maybe it will produce poisonous gas when burning,non-professional personnel can not do combustion disposal,should be sent to garbage power plant or
garbage burning place treatment.
Transportation storage
Sealed storage in the cool and dry place.The warranty period is 12 months.Keep away from dangerous sources during storage and transportation.Avoid placing it upside down, knocking against and transporting it as a non-dangerous
product during transportation.
Packaging specification
2 components, 10kg/set,plastic drums + carton packaging.